Porty v MIDI
pisu tu takuto vec:
Network 2 units for 16 MIDI IN and OUT and 256 MIDI channels via 8-pin network port *
no a ta hviezdicka je nasledujuce vysvetlenie:
* Networking only available under MacOS or Windows XP, however, Clockworks for Windows only supports editing the first device in a network.
a teraz neviem ci ta siet funguje len ked je to zapnute na PC alebo MAC. alebo som si to len zle prelozil...
Network 2 units for 16 MIDI IN and OUT and 256 MIDI channels via 8-pin network port *
no a ta hviezdicka je nasledujuce vysvetlenie:
* Networking only available under MacOS or Windows XP, however, Clockworks for Windows only supports editing the first device in a network.
a teraz neviem ci ta siet funguje len ked je to zapnute na PC alebo MAC. alebo som si to len zle prelozil...
inde citam :
NETWORKING
For those of you with larger MIDI rigs, the MTP AV's Network serial port can be used to connect a second MTP AV to provide connections 9-16, or even to link up to a standard 16-channel MIDI interface. It can also serve as a second connection to the Macintosh, although this is not normally necessary with most applications which can use the multi-port capabilities of the unit. This capability is provided for compatibility with software which does not support the multi-port MTP standard.
It's actually possible to connect up to four MTP devices to your Mac, using two on each serial port -- modem and printer. In this case, there would be a free Mac port on each box providing connections 9-16, as the pairs of MTPs are connected using the network socket. You could use these to hook up a second Mac, which would then have equal access to the complete MIDI system. You can even connect both a Macintosh and a PC to the MTP AV at the same time, connecting the PC to the parallel port and the Mac to the network port; with this setup, the computers can even send data to each other.
NETWORKING
For those of you with larger MIDI rigs, the MTP AV's Network serial port can be used to connect a second MTP AV to provide connections 9-16, or even to link up to a standard 16-channel MIDI interface. It can also serve as a second connection to the Macintosh, although this is not normally necessary with most applications which can use the multi-port capabilities of the unit. This capability is provided for compatibility with software which does not support the multi-port MTP standard.
It's actually possible to connect up to four MTP devices to your Mac, using two on each serial port -- modem and printer. In this case, there would be a free Mac port on each box providing connections 9-16, as the pairs of MTPs are connected using the network socket. You could use these to hook up a second Mac, which would then have equal access to the complete MIDI system. You can even connect both a Macintosh and a PC to the MTP AV at the same time, connecting the PC to the parallel port and the Mac to the network port; with this setup, the computers can even send data to each other.
maly review v SOS : http://www.soundonsound.com/sos/1997_ar ... mtpav.html
pytkin : po tom vsetkom co sme tu prebrali som vlastne zistil ze ja potrebujem len vysielat co midi channel to audio channel.. cize ak ma zariadenie 4 analog out tak chcem mat len 4 midi channels( samozrejme by som mohol mat aj viac na ten jeden audio out ale to teraz nepotrebujem, ze by som ich paroval a nechal hrat do konkretneho audio vystupu )
tu je obrazok:
cize napriklad na tie EX5r pouzijem jeden port, kedze tam mam na kazdej 8 analog out, tak mi postaci na kazdy out jeden midi channel, cize prva EX5r bude mat 1-8 midi ch. a druha EX5r by mala 9-16 midi ch.
cize na jeden port takto dve zariadenia by nemala byt nejaka extra zataz, akurat ich budem musiet nastavit tie channels priamo v moduloch... a potom este urcit co je master co by bola asi XS kedze budem vyuzivat jej sequencer..
cize takto mi este ostavaju 2 porty volne na tom 8x8...
tu je obrazok:
cize napriklad na tie EX5r pouzijem jeden port, kedze tam mam na kazdej 8 analog out, tak mi postaci na kazdy out jeden midi channel, cize prva EX5r bude mat 1-8 midi ch. a druha EX5r by mala 9-16 midi ch.
cize na jeden port takto dve zariadenia by nemala byt nejaka extra zataz, akurat ich budem musiet nastavit tie channels priamo v moduloch... a potom este urcit co je master co by bola asi XS kedze budem vyuzivat jej sequencer..
cize takto mi este ostavaju 2 porty volne na tom 8x8...
